Sweeper data record (Code 11)

Sweeper data record script description

Script Description

Script is capable of collecting separate variables from multiple record codes and storing them into sensors chosen by users. A single script is capable of parsing multiple record codes. To do that, user must select which record codes they want to parse by placing check mark on "Read this record" check box.

Configuration

Inside FMSet it's possible select which variables are important and onto what specific sensor to save them (note that your device might not report a value which you're expecting, depends on device and it's configuration):

Open

Full list of record code 11 Variables

ManufID and EquipID - Manufacturer and spreader identification of the system which generates this record.

DeviceEntity - If more than one implement is mounted on the vehicle, this indicator allows to differentiate between the individual implements.

Source - Data generation source.

System time and date - Time and date is in unix format.

SwprMode - Sweeper mode (0=Transport, 1=Sweeping, 2= Sweeping left, 3= Sweeping right, 4=Wanderhosing, 5=Unload or tipping).

SwpCntLen - Total driven length while Sweeping (can start at any value at power-up, can overrun, can be reset when counters are reset).

SwpCntHrs - Total working hours while Sweeping (can start at any value at power-up, can overrun, can be reset when counters are reset).

DrivenLen - Driven length as interpreted and generated by the source (can start at any value at power-up, can overrun, can be reset when counters are reset).

RunHrs - Total of hours the system has run (time that control system is switched on); (can start at any value at power-up, can overrun, can be reset when counters are reset).

VehSpd - Vehicle speed (0 = not driving; any other value = driving)

SwprSucFanSpd - Rotation speed of suction fan as a percentage of the maximum speed.

SwprBrushSpd - Rotation speed of brush as a percentage of the maximum speed.

SwprBrushRel - Brush weight release %. 0 %= floating (full brush ground pressure due to weight), 100%= fully released (no brush ground pressure).

GeoLat - Geographic position latitude in NMEA-0183 format: DDMM.mmmmR (two fixed digits of degrees, two fixed digits of minutes and a variable number of digits for decimal-fraction of minutes, R = reference - latitude direction: N=north, S=south). Example: 3339,7334 N = 33 º 39,7334’ north.

GeoLon - Geographic position longitude in NMEA-0183 format: DDDMM.mmmmR (three fixed digits of degrees, two fixed digits of minutes and a variable number of digits for decimal-fraction of minutes, R = reference - longitude direction: E=east, W=west). Example: 11751,7598 W = 117 º 51,7598’ west

GeoSQ - Geographic position system signal quality (0=no fix, 1=2D, 2=3D, 3=differential correction active).

SwprWaterLev - Level of water in tank (0 %=empty, 100 %=full) (this record is only optional and your device might not send any value. It depends on your device configuration).

SwprHopperLd - (this record is only optional and your device might not send any value. It depends on your device configuration).

SwprBrushMov - Number of brush movements (can start at any value at power-up, can overrun, can be reset) (this record is only optional and your device might not send any value. It depends on your device configuration).

SwpErrRpt - Error report (e.g. no salt detected), could contain more than one error, separated by dashes – supplier specific code (this record is only optional and your device might not send any value. It depends on your device configuration).

BeaconOn - Beacon light is switched on (0=off, 1=on) (this record is only optional and your device might not send any value. It depends on your device configuration).

SwprOilT - Oil temperature of sweeper (this record is only optional and your device might not send any value. It depends on your device configuration).

SwprOilP - Oil working pressure on rotor (this record is only optional and your device might not send any value. It depends on your device configuration).

SwprOilQ - Oil flow through rotor (this record is only optional and your device might not send any value. It depends on your device configuration).